#################### This file is used by NXP NFC NCI HAL #####################
###############################################################################
# Application options
# Logging Levels
# NXPLOG_DEFAULT_LOGLEVEL 0x01
# ANDROID_LOG_DEBUG 0x03
# ANDROID_LOG_WARN 0x02
# ANDROID_LOG_ERROR 0x01
# ANDROID_LOG_SILENT 0x00
NXPLOG_EXTNS_LOGLEVEL=0x03
NXPLOG_NCIHAL_LOGLEVEL=0x03
NXPLOG_NCIX_LOGLEVEL=0x03
NXPLOG_NCIR_LOGLEVEL=0x03
NXPLOG_FWDNLD_LOGLEVEL=0x03
NXPLOG_TML_LOGLEVEL=0x03
NFC_DEBUG_ENABLED=1
###############################################################################
# Nfc Device Node name
NXP_NFC_DEV_NODE="/dev/nq-nci"
#################################################################################
#VEN Toggle Config
#Disable = 0x00
#Enable = 0x01
ENABLE_VEN_TOGGLE=0x00
###############################################################################
# Extension for Mifare reader enable
MIFARE_READER_ENABLE=0x01
###############################################################################
# Mifare Reader implementation
# 0: General implementation
# 1: Legacy implementation
LEGACY_MIFARE_READER=0
###############################################################################
# File name for Firmware
NXP_FW_NAME="libsn100u_fw.so"
###############################################################################
# System clock source selection configuration
#define CLK_SRC_XTAL 1
#define CLK_SRC_PLL 2
NXP_SYS_CLK_SRC_SEL=0x02
###############################################################################
# System clock frequency selection configuration
#define CLK_FREQ_13MHZ 1
#define CLK_FREQ_19_2MHZ 2
#define CLK_FREQ_24MHZ 3
#define CLK_FREQ_26MHZ 4
#define CLK_FREQ_38_4MHZ 5
#define CLK_FREQ_52MHZ 6
NXP_SYS_CLK_FREQ_SEL=0x02
###############################################################################
# The timeout value to be used for clock request acknowledgment
# min value = 0x01 to max = 0x06
#NXP_SYS_CLOCK_TO_CFG=0x06
###############################################################################
# The delay to try to start PLL/XTAL when using sys clock 256/fc units = ~18.8 us
# min value = 0x01 to max = 0x1F
#NXP_CLOCK_REQ_DELAY=0x16
###############################################################################
# NXP proprietary settings
NXP_ACT_PROP_EXTN={2F, 02, 00}
###############################################################################
# NFC forum profile settings
NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00}
###############################################################################
# NXP TVDD configurations settings
# Allow NFCC to configure External TVDD, two configurations (1 and 2) supported,
# out of them only one can be configured at a time.
NXP_EXT_TVDD_CFG=0x02
###############################################################################
#config1:SLALM, 3.3V for both RM and CM
#NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C}
###############################################################################
#config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM,
#monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms
#NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, C2, B2, 00, B2, 1E, 1F, 00, D0, 0C}
#NXP_EXT_TVDD_CFG_2={20, 02, 30, 01, A0, 0E, 2C, F0, 00, 3E, 11, E4, E4, E4, 00, 00, 00, 00, 00, A7, 8E, FF, FF, 0F, 0F, 0F, 0F, 0A, 00, 00, 00, 00, 02, 00, 00, 01, 00, 10, 00, 04, 00, 00, 00, 17, 40, 20, 07, 13, 07, 05, 13}
# *** IGUANA_LITE40x20 FW VERSION = 01.10.53 ***
NXP_RF_CONF_BLK_1={
20, 02, E5, 05,
A0, 0E, 2C, F0, 00, 3E, 11, E4, E4, E4, 00, 00, 00, 00, 00, A7, 8E, FF, FF, 1C, 1C, 1C, 1C, 0A, 00, 00, 00, 00, 02, 00, 00, 01, 00, 10, 00, 04, 00, 00, 00, 17, 40, FF, 07, 13, 07, 05, 13,
A0, A4, 85, 14, 00, 01, 00, 00, 00, 00, 00, 00, 01, 00, 03, 00, 05, 00, 07, 00, 08, 00, 0A, 00, 0C, 00, 0E, 00, 10, 00, 11, 00, 13, 00, 14, 00, 16, 00, 18, 00, 19, 00, 1A, 00, 1C, 00, 1D, 00, 1F, 00, 20, 00, 21, 00, 24, 00, 25, 00, 27, 00, 29, 00, 2A, 00, 2C, 00, 2D, 00, 2F, 00, 31, 00, 32, 00, 34, 00, 35, 00, 37, 00, 39, 00, 3A, 00, 3C, 00, 3D, 00, 3F, 00, 41, 00, 42, 00, 44, 00, 46, 00, 47, 00, 49, 00, 4A, 00, 4C, 00, 4E, 00, 4F, 00, 51, 00, 52, 00, 54, 00, 56, 00, 57, 00, 59, 00, 5A, 00, 5C, 00, 5E, 00, 5F, 00, 61, 00, 62, 00, 64, 00,
A0, 11, 07, 01, 0A, 32, 01, C8, F6, F6,
A0, A5, 0D, 3B, 3B, 3B, 3B, 3B, 3B, FF, 03, 1F, 00, 3B, 00, 00,
A0, 6A, 10, B4, 00, B4, 00, B4, 00, B4, 00, 64, 05, 64, 05, 64, 05, 64, 05
}
NXP_RF_CONF_BLK_2={
20, 02, CC, 01,
A0, 34, C8, 23, 04, 3D, 01, 07, 19, C5, 07, 00, 00, 53, 09, 00, 00, E1, 0A, 00, 00, E1, 0A, 00, 00, 6F, 0C, 00, 00, 6F, 0C, 00, 00, 8A, 0F, 00, 00, 8A, 0F, 00, 00, A6, 12, 00, 00, A6, 12, 00, 00, C1, 15, 00, 00, C1, 15, 00, 00, DD, 18, 00, 00, DD, 18, 00, 00, DD, 18, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 03, 19, EF, 00, 00, 00, 8E, 01, 00, 00, 55, 02, 00, 00, CC, 02, 00, 00, 93, 03, 00, 00, 0A, 04, 00, 00, F9, 04, 00, 00, AF, 06, 00, 00, 03, 09, 00, 00, 6F, 0C, 00, 00, A6, 12, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00, 29, 3E, 00, 00
}
NXP_RF_CONF_BLK_3={
20, 02, 66, 01,
A1, 0A, 62, 09, 18, 7A, 03, 00, 00, 7A, 03, 00, 00, 7A, 03, 00, 00, 7A, 03, 00, 00, 7A, 03, 00, 00, 78, 05, 00, 00, 08, 07, 00, 00, FC, 08, 00, 00, FC, 08, 00, 00, 92, 09, 00, 00, 92, 09, 00, 00, DC, 0A, 00, 00, DC, 0A, 00, 00, 48, 0D, 00, 00, 30, 11, 00, 00, 30, 11, 00, 00, 8E, 12, 00, 00, 7C, 15, 00, 00, 70, 17, 00, 00, 58, 1B, 00, 00, 40, 1F, 00, 00, 28, 23, 00, 00, 28, 23, 00, 00, 28, 23, 00, 00
}
NXP_RF_CONF_BLK_4={
20, 02, F1, 01,
A0, A9, ED, 00, 2A, FF, 01, 24, FF, 02, 1F, FF, 03, 1A, FF, 04, 16, FF, 05, 12, FF, 06, 0F, FF, 07, 0C, FF, 08, 09, FF, 09, 07, FF, 0A, 05, FF, 0B, 03, FF, 0C, 01, FF, 0D, 00, F5, 0E, 00, DC, 0F, 00, C6, 10, 00, B3, 11, 00, A2, 12, 00, 92, 13, 00, 84, 14, 00, 77, 15, 00, 6B, 16, 00, 60, 17, 00, 57, 18, 00, 4E, 19, 00, 46, 1A, 00, 3F, 1B, 00, 39, 1C, 00, 33, 1D, 00, 2E, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A, 1E, 00, 2A
}
NXP_RF_CONF_BLK_5={
20, 02, E9, 06,
A0, 0B, BB, 77, 1D, 01, 14, 6A, 2A, E8, 03, E8, 03, 06, 10, 0E, 2C, 01, 78, 13, 00, 00, 78, 13, 00, 00, 78, 13, 00, 00, 78, 13, 00, 00, 78, 13, 00, 00, 78, 13, 00, 00, 78, 13, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 0A, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 78, 00, 00, 00, 3C, 00, 00, 00, 3C, 00, 00, 00, 3C, 00, 00, 00, 00, 00, 00, 00,
A0, A6, 03, C0, 08, 08,
A0, 0D, 06, 62, 32, AE, 00, 7F, 00,
A0, 0D, 06, 67, 32, AE, 00, 1F, 00,
A0, 0D, 06, 82, 82, 43, 80, 00, 00,
A0, 0D, 06, 80, 82, 4F, 80, 00, 00
}
NXP_RF_CONF_BLK_6={
20, 02, E9, 05,
A0, AB, 82, 27, 1B, 33, 04, 42, 04, 55, 04, 75, 04, 9E, 04, C7, 04, F0, 04, 20, 05, 4F, 05, 7F, 05, B8, 05, F2, 05, 2B, 06, 72, 06, BA, 06, 02, 07, 49, 07, 91, 07, F0, 07, 50, 08, AF, 08, 0F, 09, 6E, 09, E1, 09, 54, 0A, C6, 0A, 56, 0B, E5, 0B, 74, 0C, 04, 0D, 93, 0D, 52, 0E, 11, 0F, D0, 0F, 8F, 10, 4F, 11, 0E, 12, 2C, 13, 4B, 14, 6A, 15, 88, 16, A7, 17, C6, 18, 44, 1A, C2, 1B, 41, 1D, BF, 1E, 9D, 20, 7B, 22, 58, 24, 96, 26, D3, 28, 11, 2B, 4E, 2D, 4B, 30, 47, 33, 44, 36, 40, 39, 3D, 3C, A2, 3F, 07, 43, 6C, 46, E6, 4A, 61, 4F,
A0, A7, 0B, 00, 02, 77, 17, 1F, 1F, 1F, 0A, FF, 19, 05,
A0, A8, 38, 00, 33, 33, 10, 00, 33, 23, 10, 00, 33, 24, 10, 4B, 23, 44, 10, CF, 22, 43, 10, CF, 22, 43, 10, CF, 22, 43, 10, CE, 22, 43, 10, CF, 22, 43, 10, CE, 22, 43, 10, 00, 33, 22, 10, C0, 22, 23, 10, 00, 33, 22, 10, C0, 22, 23, 10,
A0, 98, 08, 6E, DD, 18, 80, 1C, 6E, 6E, 6E,
A0, 9E, 0C, 0B, DD, 18, 96, 00, 2C, 01, 2B, 52, 03, 00, 00
}
NXP_RF_CONF_BLK_7={
20, 02, FB, 14,
A0, C6, 5B, 00, 00, 04, 00, 00, 00, 3C, 00, 00, 00, 20, 80, FF, 01, 00, 00, 64, 00, 00, C0, 00, 00, 00, C0, 00, 00, 00, 01, 01, 01, 20, 01, 03, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00,
A0, 0D, 06, 10, C9, 30, 00, 40, 00,
A0, 0D, 03, 24, 29, 07,
A0, 0D, 03, 24, 30, 07,
A0, 0D, 03, 25, 29, 01,
A0, 0D, 03, 25, 30, 01,
A0, 0D, 06, 40, 42, F0, C1, 37, CC,
A0, 0D, 06, 41, 45, 31, 12, 00, 00,
A0, 0D, 03, 42, 7C, 54,
A0, 0D, 06, 42, 8D, 00, A0, A4, 64,
A0, 0D, 06, 42, 8B, 00, A2, 23, 00,
A0, 0D, 06, 42, 89, 7F, 12, BD, 01,
A0, 0D, 06, 42, 44, 00, B0, 66, 01,
A0, 0D, 06, 42, 43, 24, 24, 4D, ED,
A0, 0D, 06, 42, 41, FD, FF, 5F, F0,
A0, 0D, 06, 42, 40, 08, 77, 33, 3A,
A0, 0D, 06, 42, 4A, 00, 00, 00, 00,
A0, 0D, 06, 42, 49, 00, 00, 00, 00,
A0, 0D, 06, 51, 40, 12, 77, 33, 3A,
A0, 0D, 06, 43, 44, 00, 34, 52, 01
}
NXP_RF_CONF_BLK_8={
20, 02, FD, 1C,
A0, 0D, 06, 43, 43, A5, 64, 4C, AD,
A0, 0D, 06, 43, 40, 05, 77, 33, 3D,
A0, 0D, 06, 43, 4A, 00, 00, 00, 00,
A0, 0D, 06, 43, 49, 00, 00, 00, 00,
A0, 0D, 06, 44, 44, 00, 34, 52, 01,
A0, 0D, 06, 44, 43, A5, 64, 4C, AD,
A0, 0D, 06, 44, 40, 05, 77, 33, 3D,
A0, 0D, 06, 44, 4A, 00, 00, 00, 00,
A0, 0D, 06, 44, 49, 00, 00, 00, 00,
A0, 0D, 06, 45, 44, 00, 34, 52, 01,
A0, 0D, 06, 45, 43, A5, 64, 4C, AD,
A0, 0D, 06, 45, 40, 05, 77, 33, 3D,
A0, 0D, 06, 45, 4A, 00, 00, 00, 00,
A0, 0D, 06, 45, 49, 00, 00, 00, 00,
A0, 0D, 06, 46, 45, 39, 12, 00, 00,
A0, 0D, 06, 46, 44, 00, 34, 52, 01,
A0, 0D, 06, 47, 43, A5, 64, 4C, ED,
A0, 0D, 06, 47, 40, 05, 77, 33, 3D,
A0, 0D, 06, 47, 4A, 20, AA, 0B, 81,
A0, 0D, 06, 47, 49, B5, 44, 22, 00,
A0, 0D, 06, 48, 43, A5, 64, 4C, AD,
A0, 0D, 06, 48, 40, 05, 77, 33, 3D,
A0, 0D, 06, 48, 4A, 00, 00, 00, 00,
A0, 0D, 06, 48, 49, 00, 00, 00, 00,
A0, 0D, 06, 49, 43, A5, 64, 4C, AD,
A0, 0D, 06, 49, 40, 05, 77, 33, 3D,
A0, 0D, 06, 49, 4A, 00, 00, 00, 00,
A0, 0D, 06, 49, 49, 00, 00, 00, 00
}
NXP_RF_CONF_BLK_9={
20, 02, FA, 1C,
A0, 0D, 06, 4A, 8B, 48, 02, F0, 80,
A0, 0D, 06, 4A, 43, A5, 64, 4C, AD,
A0, 0D, 06, 4A, 40, 05, 77, 33, 3D,
A0, 0D, 06, 4A, 4A, 00, 00, 00, 00,
A0, 0D, 06, 4A, 49, 00, 00, 00, 00,
A0, 0D, 06, 4B, 43, A5, 64, 4C, 6D,
A0, 0D, 06, 4C, 44, 00, 34, 52, 01,
A0, 0D, 06, 4C, 4A, 00, 00, 00, 00,
A0, 0D, 06, 4C, 49, 00, 00, 00, 00,
A0, 0D, 06, 4C, 40, 85, 51, 33, 3D,
A0, 0D, 06, 4D, 44, 00, 34, 52, 01,
A0, 0D, 06, 4D, 4A, 00, 00, 00, 00,
A0, 0D, 06, 4D, 49, 00, 00, 00, 00,
A0, 0D, 06, 4D, 40, 85, 51, 33, 3D,
A0, 0D, 06, 4E, 45, 31, 12, 00, 00,
A0, 0D, 03, 4E, 7C, 50,
A0, 0D, 06, 4E, 8D, 00, 00, 00, 06,
A0, 0D, 06, 4E, 8B, 00, A2, 24, 00,
A0, 0D, 06, 4E, 89, 7D, 84, 05, 08,
A0, 0D, 06, 4E, 44, 00, B0, 66, 01,
A0, 0D, 06, 4E, 43, A5, 64, 5C, AD,
A0, 0D, 06, 4E, 41, FD, FF, 5F, F0,
A0, 0D, 06, 4E, 40, 07, 77, 33, 3D,
A0, 0D, 06, 4F, 4A, 2A, 8E, 8D, 2A,
A0, 0D, 06, 4F, 49, 5D, 27, 27, 00,
A0, 0D, 06, 50, 4A, 00, 00, 00, 00,
A0, 0D, 06, 50, 49, 00, 00, 00, 00,
A0, 0D, 06, 52, 4A, 00, 00, 00, 00
}
NXP_RF_CONF_BLK_10={
20, 02, FD, 1C,
A0, 0D, 06, 52, 49, 00, 00, 00, 00,
A0, 0D, 06, 53, 4A, 00, 00, 00, 00,
A0, 0D, 06, 53, 49, 00, 00, 00, 00,
A0, 0D, 06, 60, 4E, FF, FF, FF, 01,
A0, 0D, 06, 60, 4F, FF, FF, FF, 01,
A0, 0D, 06, 60, 50, FF, FF, FF, 3F,
A0, 0D, 06, 80, 7D, A0, 00, 96, BF,
A0, 0D, 06, 80, 80, 42, 00, 04, 00,
A0, 0D, 06, 80, C9, 30, 00, 00, 00,
A0, 0D, 06, 8C, 80, 41, 00, 04, 00,
A0, 0D, 06, 90, 4F, FF, FF, F0, 01,
A0, 0D, 06, 90, 4E, FF, FF, F0, 01,
A0, 0D, 06, 90, 39, 3F, 00, 00, 61,
A0, 0D, 06, 9B, A9, 84, 00, 00, 00,
A0, 0D, 06, 9B, A1, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9B, 99, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9B, 95, FF, 00, 0F, 00,
A0, 0D, 06, 9B, A5, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9B, 9D, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9B, 97, FF, 00, 0F, 00,
A0, 0D, 06, 9B, 4F, FF, FF, FF, 01,
A0, 0D, 06, 9B, 4E, FF, FF, FF, 01,
A0, 0D, 06, 91, D4, F8, 84, EF, 03,
A0, 0D, 06, 91, D2, 4A, 4A, 4B, 38,
A0, 0D, 06, 9C, A9, 84, 00, 00, 00,
A0, 0D, 06, 9C, A1, 7F, 22, 5F, 00,
A0, 0D, 06, 9C, 99, 7F, 22, 7F, 7F,
A0, 0D, 06, 9C, 95, FF, 00, 0F, 00
}
NXP_RF_CONF_BLK_11={
20, 02, F5, 17,
A0, 0D, 06, 9C, A5, 7F, 22, 5F, 00,
A0, 0D, 06, 9C, 9D, 7F, 22, 7F, 7F,
A0, 0D, 06, 9C, 97, FF, 00, 0F, 00,
A0, 0D, 06, 9C, 4F, 9F, 88, FF, 01,
A0, 0D, 06, 9C, 4E, 9F, 88, FF, 01,
A0, 0D, 06, 95, D4, F8, 84, 75, 00,
A0, 0D, 06, 95, D2, 4A, 4B, 4B, 58,
A0, 0D, 06, 9D, A9, 84, 00, 00, 00,
A0, 0D, 06, 9D, A1, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9D, 99, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9D, 95, FF, 00, 0F, 00,
A0, 0D, 06, 9D, A5, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9D, 9D, 7F, 7F, 7F, 7F,
A0, 0D, 06, 9D, 97, FF, 00, 0F, 00,
A0, 0D, 06, 9D, 4F, FF, FF, FF, 01,
A0, 0D, 06, 9D, 4E, FF, FF, FF, 01,
A0, 0D, 06, 99, D4, F8, 04, E4, 01,
A0, 0D, 06, 99, D2, 4A, 4B, 4B, 48,
A0, AF, 09, 11, 6E, 00, 1C, 11, 6E, 00, 1C, 00,
A0, 92, 28, 37, 00, 1B, 00, FC, 81, 0F, 00, 22, 80, 0F, 00, 14, 00, 20, 70, EA, 01, 43, 18, 32, 16, 78, 30, 0D, 00, 03, 55, EA, 05, 01, 04, 68, 02, 3F, 92, 04, 00, 0C, 13,
A0, 1F, 06, 63, 00, 42, 00, 14, 00,
A0, 9A, 02, 00, 00,
A0, 99, 0A, 03, 00, 80, 00, 00, 80, 00, 00, 00, 00
}
NXP_RF_CONF_BLK_12={
20, 02, 34, 02,
A0, 68, 2A, 06, 40, 60, 03, 19, 00, 00, 00, 00, 82, 04, 00, C0, 04, 00, 0F, FF, 7F, 00, 0F, FF, 7F, A0, 00, 03, FA, 00, 00, 00, 4C, 00, 14, 00, 7D, 00, 05, 7F, 00, 00, 01, 00, 03,
A0, 0D, 03, 61, 09, 80
}
NXP_RF_CONF_MAX_NUM=12
###############################################################################
# Set configuration optimization decision setting
# Enable = 0x01
# Disable = 0x00
NXP_SET_CONFIG_ALWAYS=0x01
###############################################################################
# Core configuration rf field filter settings to enable set to 01 to disable set to 00 last bit
#NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00}
###############################################################################
# To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set
# to 0x00
#NXP_I2C_FRAGMENTATION_ENABLED=0x00
###############################################################################
# Core configuration extensions
# It includes
# Wired mode settings A0ED, A0EE
# Tag Detector A040, A041, A043
# Low Power mode A007
# Clock settings A002, A003
# PbF settings A008
# Clock timeout settings A004
# eSE (SVDD) PWR REQ settings A0F2
# Window size A0D8
# DWP Speed A0D5
# How eSE connected to PN553 A012
# UICC2 bit rate A0D1
# SWP1A interface A0D4
# DWP intf behavior config, SVDD Load activated by default if set to 0x31 A037
# Low power tag detection LPTD for power reduction A068
NXP_CORE_CONF_EXTN={20, 02, 15, 05,
A0, 07, 01, 01,
A0, 8E, 01, 01,
A0, EC, 01, 01,
A0, ED, 01, 01,
A0, 0A, 01, 20
}
# A0, F2, 01, 01,
# A0, 40, 01, 01,
# A0, 41, 01, 02,
# A0, 43, 01, 04,
# A0, 02, 01, 01,
# A0, 03, 01, 11,
# A0, 07, 01, 03,
# A0, 08, 01, 01
# }
###############################################################################
# Core configuration settings
NXP_CORE_CONF={ 20, 02, 37, 11,
28, 01, 00,
21, 01, 00,
30, 01, 08,
31, 01, 03,
32, 01, 20,
38, 01, 01,
33, 04, 01, 02, 03, 04,
54, 01, 06,
50, 01, 02,
5B, 01, 00,
3E, 01, 00,
80, 01, 01,
81, 01, 01,
82, 01, 0E,
18, 01, 01,
68, 01, 01,
85, 01, 01
}
###############################################################################
#set autonomous mode
# disable autonomous 0x00
# enable autonomous 0x01
NXP_AUTONOMOUS_ENABLE=0x00
###############################################################################
#set Guard Timer
# Gurad Timer range to 0x0F-0xFF(i.e.15-255 seconds)
NXP_GUARD_TIMER_VALUE=0x0F
###############################################################################
#Enable SWP full power mode when phone is power off
#NXP_SWP_FULL_PWR_ON=0x00
################################################################################
#This is used to configure UICC2 at boot time.
# UICC2 0x03
NXP_DEFAULT_UICC2_SELECT=0x03
###############################################################################
# CE when Screen state is locked
# This setting is for DEFAULT_AID_ROUTE,
# DEFAULT_DESFIRE_ROUTE and DEFAULT_MIFARE_CLT_ROUTE
# Disable 0x00
# Enable 0x01
NXP_CE_ROUTE_STRICT_DISABLE=0x01
###############################################################################
#Timeout in secs
NXP_SWP_RD_TAG_OP_TIMEOUT=20
###############################################################################
#Set the default AID route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
# UICC 0x02
# UICC2 0x03
DEFAULT_AID_ROUTE=0x02
###############################################################################
#Set the ISODEP (Mifare Desfire) route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
# UICC 0x02
# UICC2 0x03
DEFAULT_ISODEP_ROUTE=0x02
###############################################################################
#Set the Mifare CLT route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
# UICC 0x02
# UICC2 0x03
DEFAULT_MIFARE_CLT_ROUTE=0x02
###############################################################################
#Set the Felica CLT route Location :
#This settings will be used when application does not set this parameter
# eSE 0x01
# UICC 0x02
# UICC2 0x03
DEFAULT_FELICA_CLT_ROUTE=0x02
###############################################################################
#Set the default AID Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
DEFAULT_AID_PWR_STATE=0x3B
###############################################################################
#Set the Mifare Desfire Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
DEFAULT_DESFIRE_PWR_STATE=0x3B
###############################################################################
#Set the Mifare CLT Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
DEFAULT_MIFARE_CLT_PWR_STATE=0x3B
###############################################################################
#Set the Felica CLT Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
DEFAULT_FELICA_CLT_PWR_STATE=0x3B
###############################################################################
#Set the T4TNfcee AID Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
DEFAULT_T4TNFCEE_AID_POWER_STATE=0x3B
###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
# UICC 0x02
# UICC2 0x03
DEFAULT_SYS_CODE_ROUTE=0x02
###############################################################################
# AID Matching platform options
# AID_MATCHING_L 0x01
# AID_MATCHING_K 0x02
#AID_MATCHING_PLATFORM=0x01
###############################################################################
# P61 interface options
# SPI 0x02
NXP_P61_LS_DEFAULT_INTERFACE=0x02
###############################################################################
#CHINA_TIANJIN_RF_SETTING
#Enable 0x01
#Disable 0x00
#NXP_CHINA_TIANJIN_RF_ENABLED=0x01
###############################################################################
#SWP_SWITCH_TIMEOUT_SETTING
# Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60].
# Timeout in milliseconds, for example
# No Timeout 0x00
# 10 millisecond timeout 0x0A
#NXP_SWP_SWITCH_TIMEOUT=0x0A
###############################################################################
# Flashing Options Configurations
# FLASH_UPPER_VERSION 0x01
# FLASH_DIFFERENT_VERSION 0x02
# FLASH_ALWAYS 0x03
NXP_FLASH_CONFIG=0x02
###############################################################################
# P61 interface options for JCOP Download
# SPI 0x02
NXP_P61_JCOP_DEFAULT_INTERFACE=0x02
###############################################################################
# Option to perform LS update every boot
# Enable 0x01
# Disable 0x00
NXP_LS_FORCE_UPDATE_REQUIRED=0x00
###############################################################################
# Option to perform JCOP update every boot
# Enable 0x01
# Disable 0x00
NXP_JCOP_FORCE_UPDATE_REQUIRED=0x00
###############################################################################
# Bail out mode
# If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
# Set this parameter value to 1 if Android Beam is enabled, else set to 0.
NFA_POLL_BAIL_OUT_MODE=0x00
###############################################################################
# White list of Hosts
# This values will be the Hosts(NFCEEs) in the HCI Network.
DEVICE_HOST_WHITE_LIST={C0, 80}
###############################################################################
# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1.
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check
# command is sent waiting for rsp and ntf.
PRESENCE_CHECK_ALGORITHM=2
###############################################################################
# Options to Fallback to alternative route
# Disable 0x00
# DH 0x01
# ESE 0x02
NXP_CHECK_DEFAULT_PROTO_SE_ID=0x01
###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
# byte[0] NCI_PROTOCOL_18092_ACTIVE
# byte[1] NCI_PROTOCOL_B_PRIME
# byte[2] NCI_PROTOCOL_DUAL
# byte[3] NCI_PROTOCOL_15693
# byte[4] NCI_PROTOCOL_KOVIO
# byte[5] NCI_PROTOCOL_MIFARE
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, FF, FF, FF}
###############################################################################
#NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE
#Enable/Disable block number checks for china transit use case
#Enable 0x01
#Disable 0x00
#NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE=0x01
###################################################################################################
#This flags will enable different modes of Lx Debug based on bits of the Byte0 & Byte1
#Byte 0:
# |_________Bit Mask_______| Debug Mode
# b7|b6|b5|b4|b3|b2|b1|b0|
# | | |X | | | | | Enable L1 Events (ISO14443-4, ISO18092)
# | | | |X | | | | Enable L2 Reader Events(ROW specific)
# | | | | |X | | | Enable Felica SystemCode
# | | | | | |X | | Enable Felica RF (all Felica CM events)
# | | | | | | |X | Enable L2 Events Card Emulation (ISO14443-3, Modulation detected, RF Field ON/OFF)
#Byte 1:
# Enable RSSI 0x01 Byte1 Byte0
# Disable RSSI 0x00 \__ __/
# e.g. NXP_CORE_PROP_SYSTEM_DEBUG=0x0110 ==> L1 with RSSI
NXP_CORE_PROP_SYSTEM_DEBUG=0x0000
###############################################################################
#Enable NXP NCI runtime parser library
#Enable 0x01
#Disable 0x00
NXP_NCI_PARSER_LIBRARY=0x00
###############################################################################
# Timeout value in milliseconds for JCOP OS download to complete
OS_DOWNLOAD_TIMEOUT_VALUE=60000
###############################################################################
# Forcing HOST to listen for a selected protocol
# 0x00 : Disable Host Listen
# 0x01 : Enable Host to Listen (A) for ISO-DEP tech A
# 0x02 : Enable Host to Listen (B) for ISO-DEP tech B
# 0x04 : Enable Host to Listen (F) for T3T Tag Type Protocol tech F
# 0x07 : Enable Host to Listen (ABF)for ISO-DEP tech AB & T3T Tag Type Protocol tech F
HOST_LISTEN_TECH_MASK=0x07
###############################################################################
# Enable forward functionality
# Disable 0x00
# Enable 0x01
FORWARD_FUNCTIONALITY_ENABLE=0x00
###############################################################################
# Configure the NFC Extras to open and use a static pipe. If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
# for each EE (ESE/SIM1/SIM2)
OFF_HOST_ESE_PIPE_ID=0x16
OFF_HOST_SIM_PIPE_ID=0x0A
OFF_HOST_SIM2_PIPE_ID=0x23
###############################################################################
#Set the Felica T3T System Code Power state :
#This settings will be used when application does not set this parameter
#Update Power state as per NCI2.0
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen On lock
# bit pos 4 = Screen off unlock
# bit pos 5 = Screen Off lock
DEFAULT_SYS_CODE_PWR_STATE=0x00
###############################################################################
#Default Secure Element route id
DEFAULT_OFFHOST_ROUTE=0x02
###############################################################################
#Maximum SMB transceive wait for response
NXP_SMB_TRANSCEIVE_TIMEOUT=2000
###############################################################################
# Firmware file type
#.so file 0x01
#.bin file 0x02
NXP_FW_TYPE=0x01
############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF
#########################################################################
# Support for Amendment I SEMS specification
# Support SEMS Amendment I 0x01
# Support NXP LS client 0x00
NXP_GP_AMD_I_SEMS_SUPPORTED=0x01
###############################################################################
#All eSE terminals shall be match with the /vendor/etc/vintf/manifest.xml file
#under android.hardware.secure_element
# The terminal name shall start from 1
# Assign terminal number to each interface based on system config
NXP_SPI_SE_TERMINAL_NUM="eSE1"
###############################################################################
# Assign terminal number to each interface based on system config
#NXP_VISO_SE_TERMINAL_NUM="eSE3"
###############################################################################
# Assign terminal number to each interface based on system config
NXP_NFC_SE_TERMINAL_NUM="eSE2"
###############################################################################
#For static or dynamic dual UICC feature support
#Enable static dual uicc feature by setting value 0x00
#Enable dynamic dual uicc feature by setting value 0x01
NXP_DUAL_UICC_ENABLE=0x01
###############################################################################
# Time to wait by DH when NFCC will report eSE Cold Temp Error.
# The value is as per the UM and in seconds
NXP_SE_COLD_TEMP_ERROR_DELAY=0x05
###############################################################################
#OffHost ESE route location for MultiSE
#ESE = 01
OFFHOST_ROUTE_ESE={01}
###############################################################################
#OffHost UICC route location for MultiSE
#UICC1 = 02
#UICC2 = 03
OFFHOST_ROUTE_UICC={02:03}
###############################################################################
#T4T NFCEE ENABLE
#bit pos 0 = T4T NFCEE Enable
#bit pos 6 = T4T NFCEE Contactless write enable
NXP_T4T_NFCEE_ENABLE=0x01
###############################################################################
#CORE_SET_CONF_CMD to reset Prop Emvco Flag
NXP_PROP_RESET_EMVCO_CMD={20, 02, 05, 01, A0, 44, 01, 00}
###############################################################################
#Guard time in ms for the mPOS/SCR module to process the reader start/stop req
NXP_RDR_REQ_GUARD_TIME=0
###############################################################################
# Firmware patch format, Only 1 and 5 should be set
# 0 -> NFC Default
# 1 -> EMVCO Default
# 3 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = Removal process
# 5 -> EMVCO Cert Polling, DISC_IDLE = Removal process , DISC DEACTIVATE = POWER_OFF
# 7 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = POWER_OFF
NFA_CONFIG_FORMAT=1
################################################################################
# This will enable power state required for GSMA testing.
# When this is enabled , then default AID route power state is added with this power state
# If any aid with power state 0 is added, then this power state is used.
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen off unlock
# bit pos 4 = Screen On lock
# bit pos 5 = Screen Off lock
#DEFUALT_GSMA_PWR_STATE=0x3B
#################################################################################
# Enable disconnect tag in screen off
# Disable 0x00
# Enable 0x01
NXP_DISCONNECT_TAG_IN_SCRN_OFF=0x01
#################################################################################